Table of Acronyms

Refer to the exhibit.

An administrator is configuring an MPLS and VPLS Martini to connect customer Sites 1, 2, and 3. The administrator has created Virtual Switch Instance (VSI) "CustomerA" for this purpose.
How should the administrator connect customer Site 1 to the VPLS solution?

• A. Create a service instance on the VLAN assigned to g1/0/1. Also create a global cross-connect group, and bind the CustomerA VSI and the service instance in that group.
• B. Create a service instance on g1/0/1. Also create a global cross-connect group, and bind the CustomerA VSI and the service instance in that group.
• C. Create a service instance on g1/0/1. Bind (cross-connect) that instance to the CustomerA VSI.
• D. Create a service instance on the VLAN assigned to g1/0/1. Bind (cross-connect) that instance to the CustomerA VSI.

What is one benefit of the HP patent for Adaptive Multicast channel width and Guard Interval 802.11n?

• A. HP APs can adapt the precise frequency on which they transmit to each client, enabling them to transmit multicasts to more than one clients at the same time.
• B. HP APs can adjust whether they send multicasts over a bonded channel based on the 802.11 standards supported on device in the current environment.
• C. HP APs can bind up to three channels together for any multicast transmissions in the 5 GHz frequency range, including 802.11a and 802.11n.
• D. HP APs can transmit multicasts as broadcasts or unicasts, helping to ensure higher transmission rates and more reliable delivery for multicast.

Table of Acronyms Refer to the exhibit.


An administrator is setting up MPLS Layer 2 VPN connections between several customer sites:
-Connection 1 = Customer site 1 to customer site 2 -Connection 2=Customer site 1 to customer site 3
On PE-1, interface GigabitEthernet1/0/1 connects to CE-1 at site 1. Which setup establishes the desired connections?

• A. CE-1 implements MPLS. It establishes two PWs with PE-1, one for its connection to CE-2 and one for its connection to CE-3. PE-1 maps the out label for the first PW to the in label for a PW to PE-2. It maps the labels similarly for a PW to PE-3.
• B. PE-1 has two policy-based routing (PBR) policies, each of which selects traffic destined to Site 2 or Site 3. The appropriate policy is applied to the PW for each connection
• C. CE-1 connects to CE-2 in one VLAN, which it assigns to VPN instance 1. It connects to CE-3 in a different VLAN, which it assigns to VPN instance 2. PE-1 instant places G1/0/1 in both VPN instances 1 and 2 and associates each VPN instance with a PW for one of the connections.
• D. CE-1 connects to CE-2 in one VLAN and to CE-3 in a different VLAN. PE-1 has two services instances on G1/D/1. One instance encapsulates one VLAN ID and has PW to PE-2, and the other instance encapsulates the other VLAN and has a PW to PE-3

Table of Acronyms

Refer to the exhibit.

An administrator wants to establish a remote LDP session between PE-1 (loopback IP address
10.0 0.1) and PE-2 (loopback IP address; 10.0.0.2). What is required to do this?

• A. Both PE-1 and PE-2 use ordered mode for LDP.
• B. Both PE-1 and PE-2 advertise their loopback IP address with OSPF and with LDP.
• C. Both PE-1 and PE-2 have a VPN instance that is defined with the same route distinguisher
  (RD)
• D. Both PE-1 and PE-2 advertise the same label for their loopback IP address

Table of Acronyms What is a benefit of enabling tandem multicast replication for SPBM?

• A. An ingress SPBM switch can load-balance multicasts over multiple equal-cost paths to a destination, even when the multicast belong to the same I-SI
• B. An ingress SPBM switch does not have the load of replicating and forwarding many copies of a multicast.
• C. Multicasts follow a better path to each destination than they would with head-end replication.
• D. SPBM switches can send multicasts as both multicasts and unicasts, increasing reliability for the transmission.

Explanation: Only visible for Actual4dump members. You can sign-up / login (it's free).