2021 Latest 100% Exam Passing Ratio - HPE6-A72 Dumps PDF
Pass Exam With Full Sureness - HPE6-A72 Dumps with 90 Questions
For more info about Aruba Certified Switching Associate (HP HPE6-A72) Professional Exam
Aruba Certified Switching Associate (HP HPE6-A72) Professional Exam
NEW QUESTION 49
Click on the colored box that corresponds with the line that best represents Broadcast traffic flow.
Answer:
Explanation:
NEW QUESTION 50
Which command can be used to find the serial number of an Aruba OS-CX switch?
- A. The command show system
- B. The command inventory
- C. The command show running-configuration
- D. The command version
Answer: A
Explanation:
Explanation/Reference:
NEW QUESTION 51
What is the correct description of a Multi-Layer Switch?
- A. multi-Layer refers specifically to using chassis switches with several line cards over stack port switches
- B. a switch with Layer 3 routing capabilities but lacks any Layer 1 features as a consequence
- C. has all the functionality of a Layer 2 switch and most of the functionality of a Layer 3 router
- D. any switch that supports PoE, LLDP-MED and Flow Control
Answer: C
NEW QUESTION 52
You need to remote into an AOS-CX switch using SSH in order to update the management IP address for future connections. Unfortunately, you mis-configured the IP address and are now locked out of the switch.
What command could you have issued before making changes that would have recovered the original switch configuration after ten minutes?
- A. boot system secondary 10
- B. checkpoint auto 10
- C. checkpoint rollback 10
- D. checkpoint auto confirm 10
Answer: B
NEW QUESTION 53
Your customer has 349 users in a two-story building.
What are two benefits of a 2-Tier design? (Choose two.)
- A. Support for WAN/MPLS, Internet, and Data Center directly on the Collapsed core.
- B. Use of layer 2 switches at the access layer can process and route traffic from attached APs.
- C. Provides a more cost effective solution given that no additional switches are required for a third tier.
- D. Layer 2 and Layer 3 protocols run close to the endpoints to better implement ACL and QoS policy at the edge.
- E. Improved performance by offloading processing from the Access layer to the Core.
Answer: C,D
NEW QUESTION 54
Match each description to the correct term.
Answer:
Explanation:
NEW QUESTION 55
ServiceOS login: admin
SVOS> password
Enter password: ********
Confirm password: ********
The login password to access an Aruba AOS-CX was lost. After connecting to the switch console port, a reboot is performed and the Service OS console is accessed as shown above.
What is the default password that is required for the admin account while under the Service OS console?
- A. The same login password that has lost originally.
- B. "forgetme!"
- C. No password is set for this account.
- D. "password"
Answer: B
Explanation:
Explanation/Reference: https://www.arubanetworks.com/techdocs/ArubaOS_83_Web_Help/Content/ArubaFrameStyles/ Management_Utilities/enab_radsec_reset_admin_enabl_pwd.htm
NEW QUESTION 56
Click on the colored box that corresponds with the line that best represents Broadcast traffic flow.
Answer:
Explanation:
NEW QUESTION 57
Refer to the exhibit.
What is the correct binary conversion of the last two hexadecimal characters of the physical address?
- A. 1001 1111 0101 0011
- B. 1101 1000
- C. 1110 1101
- D. 1000 1101 1110 1101
Answer: C
NEW QUESTION 58
The section in blue can be ignored.
SW1(config)# interface 1/1/1-1/1/2
SW1(config-if-<1/1/1-1/1/2)# vlan access 2
SW1(config-if-<1/1/1-1/1/2)# exit
SW1(config)# interface 1/1/11-1/1/17
SW1(config-if-<1/1/11-1/1/17)# vlan access 17
SW1(config-if-<1/1/11-1/1/17)# exit
After completing the above commands, what is the expected output of show vlan with no other vlan commanded having been added?
- A. Option A
- B. Option C
- C. Option B
- D. Option D
Answer: D
NEW QUESTION 59
Refer to the exhibit.
The above output is the result of issuing the command show system resource-utilization.
What command should be used to enable terminal output line by line or page by page?
- A. The command less
- B. The command more
- C. The command page
- D. The command terminal length 30
Answer: C
NEW QUESTION 60
Which two options are correct regarding the IEEE 802.11ax standard? (Choose two.)
- A. operates in both the 2.4GHz and 5GHz radios bands
- B. operates only in the 5GHz similar to 802.11ac
- C. is an emerging satellite connection standard to allow wireless access anywhere in the world
- D. allows transmissions of up to 4.8Gbps
- E. is the first WLAN standard to no longer use electromagnetic signals to transmit data
Answer: A,D
NEW QUESTION 61
What connectivity commands are available on AOS-CX switches? (Choose two.)
- A. pathping
- B. netstatus
- C. tracert
- D. traceroute
- E. ping
Answer: D,E
NEW QUESTION 62
Refer to the exhibit.
The above command was applied to an Aruba AOS-CX 6300M 24-port switch with 4-port SFP56 uplinks. All ports are set as access switchports.
Which ports carry VLAN 1 traffic?
- A. 1/1/1-1/1/24
- B. 1/1/8, 1/1/10, 1/1/5-1/1/24
- C. 1/1/1-1/1/28
- D. 1/1/8-1/1/10, 1/1/5-1/1/28
Answer: D
NEW QUESTION 63
Match the available stacking feature to the correct AOS-CX switch model. Stacking features may be used more than once.
Answer:
Explanation:
NEW QUESTION 64
Refer to the exhibit.
Traffic is failing between Core-1 and Host-B. IP addressing has correctly been applied, and all interfaces are attached to the vrf GREEN.
Which configuration will correct the issue?
- A. Core-1(config)# ip route 10.1.20.0/24 10.1.1.2 vrf GREEN Host-B: assign the default-gateway address 10.1.20.1
- B. Host-B: assign the default-gateway address 10.1.20.181
- C. Core-2(config)# ip route 0.0.0.0/0 10.1.1.1 vrf GREEN Host-B: assign the default-gateway address 10.1.20.181
- D. Core-1(config)# ip route 10.1.20.0/24 10.1.1.2 vrf GREEN Host-B: assign the default-gateway address 10.1.20.181
Answer: D
NEW QUESTION 65
Refer to the exhibit.
The above scenario shows a packet from the Server destined for the Firewall. Switch-A and Switch-B are bundled as VSF stack. The LAG between the VSF stack and the firewall indicates a hash function to forward the packet on port 2/1/2.
Which statement is true regarding how Switch-A will forward the packet?
- A. Switch-A will forward the packet along the VSF link to Switch-B so that it will egress on port 2/1/2 per the hash function.
- B. Switch-A will drop the packet. Multi-Chassis lag to multi-chassis lag is not a supported feature of VSF.
- C. Switch-A will forward the packet on port 1/1/2. VSF will override the typical LAG hash function used for the physical interface selection.
- D. Switch-A will encapsulate the packet using GRE to forward to Switch-B in order for the packet to egress on port 2/1/2 per the hash function.
Answer: A
NEW QUESTION 66
Core# configure terminal
Core(config)# vrf Green
Core(config-vrf)# exit
Core(config)#
Core(config)# interface vlan 50
Core(config-if-vlan)# ?
Given the configuration on the CORE switch shown above, what command would follow to assign the switched virtual interface (SVI) vlan 50 to the VRF created?
- A. Core(config-if-vlan)# ip vpn-instance Green
- B. Core(config-if-vlan)# vrf attach Green
- C. Core(config-if-vlan)# routing-context Green vrf
- D. Core(config-if-vlan)# ip vrf forwarding Green
Answer: B
NEW QUESTION 67
Refer to the exhibit.
What VSF command produces the above output?
- A. show vsf topology
- B. show vsf detail
- C. show vsf link
- D. show vsf member
Answer: A
NEW QUESTION 68
Match the available stacking feature to the correct AOS-CX switch model. Stacking features may be used more than once.
Answer:
Explanation:
NEW QUESTION 69
Refer to the exhibit.
What command will display the debug l2mac events?
- A. show debug terminal
- B. show module L2MAC
- C. show debug buffer module L2MAC
- D. show debug all
Answer: C
NEW QUESTION 70
Refer to the exhibit.
You are in the process of configuring VSF between Access-1 and Access-2. Access-1 has been configured as the VSF Master.
What is a valid configuration for Access-2 to join the VSF stack?
- A. Access-2# configure
Access-2(config)# vsf member 2 Access-2(vsf-member-1)# link 1 1/1/28 Access-2(vsf-member-1)# exit This will save the VSF configuration and reboot the switch. Do you want to continue (y/n)? y - B. Access-2# configure
Access-2(config)# vsf member 1 Access-2(config)# vsf renumber-to 2 Access-2(vsf-member-1)# link 2 2/1/28 Access-2(vsf-member-1)# exit This will save the VSF configuration and reboot the switch. Do you want to continue (y/n)? y - C. Access-2# configure
Access-2(config)# vsf member 2 Access-2(vsf-member-1)# link 2 1/1/28 Access-2(vsf-member-1)# exit This will save the VSF configuration and reboot the switch. Do you want to continue (y/n)? y - D. Access-2# configure
Access-2(config)# vsf member 1 Access-2(vsf-member-1)# link 1 1/1/28 Access-2(vsf-member-1)# exit Access-2(config)# vsf renumber-to 2
Answer: A
Explanation:
This will save the VSF configuration and reboot the switch. Do you want to continue (y/n)? y
NEW QUESTION 71
......
Verified HPE6-A72 dumps Q&As - 100% Pass from Actual4dump: https://www.actual4dump.com/HP/HPE6-A72-actualtests-dumps.html
Pass HPE6-A72 Exam in First Attempt Guaranteed 2021 Dumps: https://drive.google.com/open?id=1DdDzjHa87y2rzOemmzdt8Z2HSQrGDiiO