[2023] Use Valid New NACE-CIP2-001 Test Notes & NACE-CIP2-001 Valid Exam Guide
NACE-CIP2-001 Actual Questions Answers PDF 100% Cover Real Exam Questions
In addition to the NACE-CIP2-001 certification, NACE International offers a range of other certifications related to corrosion control and prevention. These certifications include the NACE-CIP1 certification for entry-level coating inspectors, the NACE-CIP3 certification for senior coating inspectors, and the NACE-CORROSION specialist certification, which covers a broad range of topics related to corrosion prevention and control. Together, these certifications provide a comprehensive framework for professional development in the corrosion control and prevention industry.
NACE-CIP2-001 Exam is designed to test candidates on their knowledge of coating inspection techniques, including surface preparation, coating application, and coating inspection. NACE-CIP2-001 exam covers a wide range of topics, including the properties of coatings, coating types and applications, coating specifications, and coating inspection procedures. Candidates must also demonstrate their ability to interpret and apply various industry standards, such as ASTM and SSPC.
NEW QUESTION # 26
You are the NACY Coating Inspector on a tank lining project where desiccant dehumidification is being used. Since the first shift of abrasive blasting your readings have indicated relative humidity below 40%; however on the second shift of coating application your readings are indicting 80%.
Your FIRST preferred course of action is to:
- A. Check to See if the dehumidification equipment is operating correctly
- B. Advise the coating applicator supervisor of your readings
- C. Document the readings at the end of the shift
- D. Call your supervisor
Answer: B
NEW QUESTION # 27
When NACE/SSPC WJ 1 is referenced; what type of equipment would the Inspector expect to see on the job:
- A. Power Tools
- B. Scarifiers
- C. Water Jetting Equipment
- D. Abrasive Blasting Equipment
Answer: C
NEW QUESTION # 28
The main reason dehumidification is used during coating operations is to
- A. control the environment
- B. avoid repetitive blasting/coating operations.
- C. allow the contractor to guarantee the completion date.
- D. reduce the possibility of missing the recoat window.
Answer: A
NEW QUESTION # 29
The solvent sensitivity/solvent wipe test (ASTM D4752) is used to determine the cure of
- A. powder coatings.
- B. urethanes.
- C. inorganic zincs.
- D. epoxies.
Answer: C
NEW QUESTION # 30
You are working as the only in-house NACE Level 2 Inspector in a shop setting when an independent 3 rd party NACE Level 3 Inspector, representing the owner, presents you with a copy of a Non Conformance Report (NCR) he has written for a NACE2/SSPC SP 10 centrifugal blast which you had previously approved.
Your FIRST preferred course of action is to:
- A. Consult your supervisor
- B. Review the NCR with the other Inspector
- C. Verbally challenge the NCR
- D. Request a re-blast of the item in question
Answer: A
NEW QUESTION # 31
When performing a hardness test on a coating which has elastic properties the inspector is likely to likely to observe:
- A. No difference from any other coating
- B. A very low reading
- C. A very high reading
- D. Cold flow or creep
Answer: D
NEW QUESTION # 32
All of these are advantages of using repair patches EXCEPT
- A. special tools or equipment are required.
- B. excellent abrasion resistance.
- C. inert to common acids, alkalis, and solvents.
- D. barrier to moisture and corrosion.
Answer: A
NEW QUESTION # 33
Corrosion is the reverse process of
- A. steel manufacturing.
- B. hot dipping.
- C. flaking.
- D. galvanic deterioration.
Answer: A
NEW QUESTION # 34
Linings are used on the interior of pipelines to
- A. afford limited temperature insulation.
- B. protect the transported product.
- C. reduce magnetic polarity.
- D. provide protection against soil chemicals.
Answer: B
NEW QUESTION # 35
The HATE adhesion tester uses
- A. a special tape to apply pressure to the test dolly.
- B. a hydraulic piston to apply pressure to the test dolly.
- C. compressed air to apply pressure to the test dolly.
- D. mechanical means only to apply pressure to the test dolly.
Answer: B
NEW QUESTION # 36
Inspection and Test Plans are provided to:
- A. To supersede the requirements of the product data sheets
- B. So the Inspector doesn't have to read the entire specification
- C. Outline the inspection steps, sequencing and pass/fail criteria
- D. So the contractor has a single document to reference
Answer: C
NEW QUESTION # 37
In the event of a conflict between the Product Data Sheet and the Specification:
- A. It is up to the Inspector to decide which one to follow
- B. It is up to the Applicator to decide which one to follow
- C. The Specification prevails
- D. The Product Data Sheet prevails
Answer: C
NEW QUESTION # 38
The Concrete Repair Institute's comparators can be used to assess:
- A. Surface cleanliness prior to coating
- B. Contamination levels prior to coating
- C. Surface profile prior to coating
- D. Compressive and tensile strength prior to coating
Answer: C
NEW QUESTION # 39
Cold-applied tape
- A. are identifiable by its distinct colors, usually light blue, green, Or Grey.
- B. have a cross-linked polyethylene backing and a heat-activated adhesive.
- C. is polyethylene film, heat laminated, 'With an adhesive layer of butyl glue.
- D. is typically green or led and looks like "painted" finish.
Answer: C
NEW QUESTION # 40
The cost of qualified Coating Inspection is normally offset by:
- A. Lower Coating Life Cycle Costs
- B. Lower Application Costs
- C. Lower Safety Enforcement Costs
- D. Lower Supervision Costs
Answer: A
NEW QUESTION # 41
A single component water borne acrylic coating cures by:
- A. Co-Reaction
- B. Coalescence
- C. Oxidation
- D. Solvent Evaporation
Answer: B
NEW QUESTION # 42
Inspectors perform tests on linings that they may not perform on exterior coatings because
- A. coatings are more durable than linings.
- B. coatings are expected to degrade over time.
- C. linings protect the contents and the container.
- D. linings are more durable than coatings.
Answer: C
NEW QUESTION # 43
When a coating is expected to be exposed to temperatures above 93C (200 F) the best choice would be:
- A. Inorganic Coatings
- B. Latex
- C. Polyurea
- D. Organic coatings
Answer: A
NEW QUESTION # 44
It is always possible to see moisture on a steel substrate:
- A. True
- B. False
Answer: B
NEW QUESTION # 45
You are NACE Level 2 Inspector working on a tank lining job where a mobile centrifugal blast unit is being used to blast the tank floor to a NACE No.1/SSPC SP 5. The Contractor has completed his final blast and has called for a hold point inspection. This is the 1 st time you have seen field based centrifugal blast cleaning. You observe what appears to be staining on the substrate however the Contractor assures you this is normal when using centrifugal blast units and what you are seeing is what is defined in the standard as an acceptable variation in appearance.
Your FIRST preferred course of action is to:
- A. Review the standard with the Contractor and re-inspect the floor
- B. Request that the Contractor re-blast the floor
- C. Call your supervisor
- D. Shut the job down
Answer: A
NEW QUESTION # 46
NACE Level 2 Inspectors have been authorized to perform:
- A. Visual inspection, Non-Destructive and Destructive testing
- B. Visual inspection and Non-destructive testing
- C. All types of inspection without supervision
- D. Visual inspection only
Answer: A
NEW QUESTION # 47
When completing the Final Inspection report the Inspector should write the report using:
- A. Language that only in the project would understand
- B. Language that another NACE Inspector would understand
- C. Language that the most would understand
- D. Language that only technical experts would understand
Answer: C
NEW QUESTION # 48
......
NACE-CIP2-001 Exam questions and answers: https://www.actual4dump.com/NACE/NACE-CIP2-001-actualtests-dumps.html
Pass NACE-CIP2-001 Exam Info and Free Practice Test: https://drive.google.com/open?id=1SAbXcSJX0YDa3BFhS95wuPjxM4X7Gi07