The Most Efficient ECP-206 Pdf Dumps For Assured Success [2023]
We offers you the latest free online ECP-206 dumps to practice
NEW QUESTION # 25
What is a label-edged router (LER)?
- A. a DR router
- B. a P router
- C. a PE router
- D. a CE router
Answer: C
Explanation:
Explanation
A label-edged router (LER) is a PE router. A PE router is a provider edge router, which is a router that connects an MPLS network to a customer network. A LER is a term used in MPLS to describe a router that resides at the ingress and egress points of an MPLS network, handling both labelled and unlabelled packets. A LER performs label operations such as adding, removing, or swapping labels on packets entering or leaving the MPLS network34.
References: What is Label Edge Router (LER)? - Definition from Techopedia, LER - Label Edge Router - Mpirical
NEW QUESTION # 26
What is the correct abbreviation for the IP address: BFEA:DACA:0000:0000:9390:0000:0000:D91?
- A. BFEA:DACA::9390::D91
- B. BFEA:DACA::D91/6
- C. BFEA:DACA::9390:0:0:D91
- D. BFEA:DACA::9390:0:D91
Answer: D
Explanation:
Explanation
The correct abbreviation for the IP address BFEA:DACA:0000:0000:9390:0000:0000:D91 is BFEA:DACA::9390:0:D91. IPv6 addresses are represented in hexadecimal notation, with eight 16-bit segments separated by colons. To simplify the address representation, IPv6 supports two types of abbreviations. The first abbreviation allows us to skip leading zeros within a segment, while the second abbreviation allows us to drop one or more consecutive segments that contain only zeros, using a double colon (::) instead. However, the double colon can be used only once in an address, to avoid ambiguity34.
References: IPv6 Address Types, Notation, and Structure Explained, IPv6 address - Wikipedia
NEW QUESTION # 27
How is a BGP session established between two routers?
- A. The BGP router sends a unicast NOTIFICATION message.
- B. The BGP router sends a unicast OPEN message.
- C. The BGP router sends a multicast HELLO packet.
- D. The BGP router sends a multicast CONNECT message.
Answer: B
Explanation:
Explanation
A BGP session is established between two routers by sending a unicast OPEN message. BGP uses TCP as its transport protocol, which means that before exchanging any BGP information, a TCP connection must be established between the routers. The TCP connection uses port 179 as both source and destination port. After establishing a TCP connection, each router sends an OPEN message to its neighbor, containing parameters such as BGP version number, AS number, hold time, BGP identifier, and optional capabilities. The OPEN message also serves as a keepalive message for BGP. If both routers agree on these parameters, they proceed to exchange UPDATE messages containing routing information and establish a BGP session.
A BGP router does not send a NOTIFICATION message to establish a session, but rather to terminate a session due to an error or a manual shutdown. A BGP router does not send a CONNECT message, as this is a TCP state, not a BGP message. A BGP router does not send a multicast HELLO packet, as this is an OSPF message, not a BGP message. References: BGP Neighbor States > BGP Fundamentals | Cisco Press, Demystifying BGP Session Establishments - Packet Pushers, The TCP/IP Guide - BGP Connection Establishment: Open Messages
NEW QUESTION # 28
Review the exhibit.
A service provider wants to connect the sites for two customers (indicated in red and green in the exhibit). The two customers are using the same IP ranges 192.168.0.0/16.
Referring to the exhibit, what should the service provider do to accomplish this task?
- A. Use a unique AS number for each customer.
- B. Connect each customer to dedicated PEs.
- C. Implement L3VPN using the MP-BGP protocol.
- D. Use a separate OSPF instance for each customer.
Answer: C
Explanation:
Explanation
Referring to the exhibit, the service provider should implement L3VPN using the MP-BGP protocol to connect the sites for two customers (indicated in red and green in theexhibit). L3VPN is a type of VPN that uses MPLS to provide IP connectivity between customer sites across a service provider network. L3VPN allows customers to use overlapping or identical IP addresses without causing conflicts or requiring NAT. L3VPN uses MP-BGP to exchange VPN routes between PE routers, which are routers that connect customer networks to the service provider network. MP-BGP is an extension of BGP that can carry multiple address families, such as VPNv4 or VPNv6, along with additional attributes, such as route distinguisher (RD) and route target (RT). RD is used to make customer routes unique within the service provider network, while RT is used to control which routes are imported or exported between different VPNs3 .
References: L3VPN - Layer 3 Virtual Private Networks - Mpirical, [Use of MP-BGP Extensions for IPv6 Interdomain Routing]
NEW QUESTION # 29
In a company network, a host sends an Ethernet frame destined to the address FF:FF:FF:FF:FF:FF.
What will an Ethernet switch do with this frame?
- A. It will send the frame only to management port.
- B. It will forward the frame to all ports.
- C. It will drop it.
- D. It will forward the frame to only one port.
Answer: B
Explanation:
Explanation
An Ethernet switch will forward the frame to all ports when the destination address is FF:FF:FF:FF:FF:FF.
This is because this address is the broadcast MAC address, which means that the frame is intended for all devices on the same LAN segment. The switch does not need to look up its MAC address table to find a matching entry for this address, but simply floods the frame out of all ports except the one where it received the frame. This way, the frame reaches every device on the LAN segment, regardless of their MAC addresses. References: Ethernet - Wireshark, Broadcast MAC Address - omnisecu.com
NEW QUESTION # 30
Which conceptual table created by routing protocols is used when processing an IP packet?
- A. forwarding information base
- B. management information base
- C. traffic engineering data base
- D. label information base
Answer: A
Explanation:
Explanation
The conceptual table created by routing protocols that is used when processing an IP packet is the forwarding information base (FIB). The FIB is a table that contains the bestroutes to reach each destination network prefix, along with the outgoing interface and the next-hop address for each route. The FIB is derived from the routing information base (RIB), which is a table that contains all the routes learned from different routing protocols and sources. The FIB is used by the router to make fast forwarding decisions for each incoming packet, based on its destination address12.
References: Security Hardening Checklist Guide for Cisco Routers/Switches in 10 Steps, VLAN - Wikipedia
NEW QUESTION # 31
Which two statements are true about route summarization? (Choose two.)
- A. It summaries the routing table entries into a default route
- B. It reduces signaling.
- C. It improves the best route calculation.
- D. It reduces the size of a routing table.
Answer: B,D
Explanation:
Explanation
Route summarization is a technique that reduces the number of routes that a router advertises to its neighbors by creating a single summary route that covers multiple subnets or networks. Route summarization has several benefits, such as:
It reduces the size of a routing table, which saves memory and CPU resources on the router. A smaller routing table also improves the lookup efficiency and convergence time of the routing protocol.
It reduces signaling, which means that less bandwidth is consumed by routing updates and less processing is required by neighboring routers. This also enhances the stability and scalability of the network, as fewer routing changes are propagated.
It improves route aggregation, which means that more specific routes are replaced by a less specific route that can be advertised to other autonomous systems or routing domains. This simplifies the inter-domain routing and hides the internal topology details.
Route summarization does not necessarily summarize the routing table entries into a default route, although a default route can be considered a special case of route summarization where all destinations are covered by one route. Route summarization also does not improve the best route calculation, as it may introduce suboptimal routing or black holes if not done properly. : Introduction to Route Summarization - NetworkLessons.com, Route Summarization > Example for Understanding Route Summarization - Cisco Press
NEW QUESTION # 32
Which two statements are correct for LDP? (Choose two.)
- A. LSRs use UDP for session establishment.
- B. LSRs send ICMP hello messages for neighbor discovery
- C. LSRs use TCP to negotiate LDP session parameters.
- D. LSRs send UDP hello messages for neighbor discovery.
Answer: C,D
Explanation:
Explanation
Two statements that are correct for LDP are:
LSRs send UDP hello messages for neighbor discovery. LDP is a protocol that distributes labels for MPLS forwarding along the shortest path calculated by an IGP. LDP uses two types of messages:
discovery messages and session messages. Discovery messages are used to discover and maintain adjacency with other LSRs that support LDP. Discovery messages are sent as UDP datagrams to the well-known multicast address 224.0.0.2 (all routers on this subnet) on port 64634.
LSRs use TCP to negotiate LDP session parameters. Session messages are used to establish, maintain, and terminate LDP sessions between LSRs. Session messages are also used to exchange label mappings, notification messages, and keepalive messages. Session messages are sent as TCP segments to port
64634.
References: Ldp | Microsoft Learn, Label Distribution Protocol - Wikipedia
NEW QUESTION # 33
An operator wants to ensure that they can differentiate their traffic types for the purpose of prioritization in their Ethernet LAN and IP/MPLS backbone.
Which three fields would be used? (Choose three.)
- A. VID
- B. ECN
- C. Traffic Class (TC)
- D. DSCP
- E. PCP
Answer: C,D,E
Explanation:
Explanation
To differentiate traffic types for the purpose of prioritization in their Ethernet LAN and IP/MPLS backbone, an operator can use the following three fields:
Traffic Class (TC): This is a 3-bit field in the MPLS label that can be used to indicate the priority or class of service (CoS) of the packet. The TC field can be mapped to the DSCP field in the IP header or the PCP field in the Ethernet header. The TC field can be used by MPLS routers to apply different per-hop behaviors (PHBs) such as queuing, scheduling, and dropping policies to different traffic classes12.
DSCP: This is a 6-bit field in the IP header that can be used to mark packets according to the differentiated services (DiffServ) model. The DSCP field can indicate the per-hop behavior (PHB) that the packet should receive at each router along its path. The DSCP field can be mapped to the TC field in the MPLS label or the PCP field in the Ethernet header. The DSCP field can be used by IP routers to provide QoS for different traffic types34.
PCP: This is a 3-bit field in the Ethernet header that can be used to mark packets according to the IEEE
802.1Q standard. The PCP field can indicate the priority or class of service (CoS) of the packet on an Ethernet LAN. The PCP field can be mapped to the TC field in the MPLS label or the DSCP field in the IP header. The PCP field can be used by Ethernet switches to provide QoS for different traffic types56.
References: MPLS Traffic Engineering - DiffServ-Aware Traffic Engineering, MPLS Traffic Engineering - DiffServ-Aware Traffic Engineering Configuration Guide, Differentiated services - Wikipedia, DSCP and Precedence Values - Cisco, 802.1Q VLAN IDs and Ethernet Interface Types - Juniper Networks, Introduction to Virtual LANs (VLANs) and Tagging - Ubiquiti Support and Help Center
NEW QUESTION # 34
Which two statements are true about link-state routing protocols? (Choose two.)
- A. A distance vector algorithm is very processor intensive compared to Dijkstra's algorithm.
- B. Each router uses a reliable update mechanism to exchange topology information with its neighbors.
C Link-state routing protocols mainly use hop-counts to determine the link cost - C. The advertisement exchange is mainly triggered by a change in the network.
Answer: B,C
Explanation:
Explanation
Link-state routing protocols are one of the two main classes of routing protocols used in packet switching networks for computer communications, the other being distance-vector routing protocols. Examples of link-state routing protocols include Open Shortest Path First (OSPF) and Intermediate System to Intermediate System (IS-IS). The basic concept of link-state routing is that every node constructs a map of the connectivity to the network, in the form of a graph, showing which nodes are connected to which other nodes. Each node then independently calculates the next best logical path from it to every possible destination in the network.
Each collection of best paths will then form each node's routing table.
Two statements that are true about link-state routing protocols are:
The advertisement exchange is mainly triggered by a change in the network. Link-state routing protocols use a flooding mechanism to distribute information about the network topology to all routers in the same area or domain. This information is encapsulated in link-state packets (LSPs) or link-state advertisements (LSAs), which contain information about the router, its directly connected links, and the state of those links. LSPs or LSAs are sent only when there is a change in the topology, such as a link failure or recovery, or when a periodic refresh timer expires. This way, link-state routing protocols can quickly adapt to network changes and maintain an accurate and consistent view of the network.
Each router uses a reliable update mechanism to exchange topology information with its neighbors.
Link-state routing protocols use a reliable update mechanism to ensure that all routers receive and acknowledge the LSPs or LSAs sent by their neighbors. This mechanism involves sending hello messages to establish and maintain adjacencies with neighbors, sending acknowledgment messages to confirm the receipt of LSPs or LSAs, and requesting missing or outdated LSPs or LSAs from neighbors.
This mechanism ensures that all routers have a synchronized database of LSPs or LSAs, which is used to build a complete network connectivity map and to calculate the shortest path to destinations.
References: Link-state routing protocol - Wikipedia, Ericsson IP Networking - Routing Protocols
NEW QUESTION # 35
Which device will fragment IPv6 packets?
- A. source host
- B. router
- C. destination host
- D. firewall
Answer: A
Explanation:
Explanation
The device that will fragment IPv6 packets is the source host. Fragmentation is a process of dividing a large packet into smaller pieces that can fit the maximum transmission unit (MTU) of the network link. In IPv4, fragmentation can be performed by either the source host or any intermediate router along the path. However, in IPv6, fragmentation is only allowed at the source host, and routers are not allowed to fragment packets. This reduces the processing overhead and complexity at routers and avoids potential fragmentation attacks. If a router receives an IPv6 packet that is too large for the next-hop link, it will drop the packet and send an ICMPv6 Packet Too Big message back to the source host56.
References: IPv6 address - Wikipedia, IPv6 Fragmentation - Cisco
NEW QUESTION # 36
Which mismatched field would cause an IS-IS adjacency between two routers to fail?
- A. MTU
- B. Context
- C. SysID
- D. SEL
Answer: A
Explanation:
Explanation
MTU mismatch would cause an IS-IS adjacency between two routers to fail. MTU stands for maximum transmission unit, which is the maximum size of a packet that can be transmitted on a link. IS-IS hellos are padded to the full MTU size, partly to allow a router to implicitly communicate its MTU to its neighbors. If two routers have different MTUs on their interfaces, they will not be able to exchange hellos properly, and their adjacency will not form or will be dropped34. To solve this problem, the MTUs on both interfaces must be configured to match.
SEL, context, and SysID are not fields that would cause an IS-IS adjacency failure. SEL stands for selector, which is a one-octet field that identifies the network layer service to which a packet should be sent. For IS-IS routers, the SEL must always be 005. Context is not a field in IS-IS packets, but rather a term used to describe the scope of routing information in different levels or areas6. SysID stands for system identifier, which is a six-octet field that uniquely identifies a router within an area. SysID does not have to match between two routers for them to form an adjacency7.
References: MTU Mismatch Problem in IS-IS - Cisco, IS-IS adjacency is not formed due to MTU mismatch - Cisco Community, IS-IS NSAP address - Cisco Community, Understanding IS-IS Routing Contexts - Juniper Networks, IS-IS - Nokia
NEW QUESTION # 37
Which operating system is used in Ericsson Router 6000 products?
- A. ERS
- B. ERS
- C. Junos
- D. IPOS
- E. SE-OS
Answer: A
Explanation:
Explanation
The operating system used in Ericsson Router 6000 products is ERS (Ericsson Router Software). ERS is based on IPOS (IP Operating System), which is a common operating system for Ericsson's IP portfolio. ERS provides advanced features and functionality for IP transport, such as MPLS, Segment Routing, QoS, IPSec, synchronization, SDN, and more. ERS also supports seamless integration with Ericsson Radio System and Ericsson Network Manager.
References: Router 6000 Series - Ericsson, Router 6675 Datasheet - Winncom
NEW QUESTION # 38
Which two protocols apply to both IPv4 and IPv6? (Choose two.)
- A. MD
- B. SNMP
- C. ARP
- D. DNS
Answer: B,D
Explanation:
Explanation
Two protocols that apply to both IPv4 and IPv6 are:
SNMP: This stands for Simple Network Management Protocol, which is a protocol that allows network administrators to monitor and manage network devices such as routers, switches, servers, printers, etc.
SNMP uses a client-server model, where an SNMP manager (client) can query or configure an SNMP agent (server) on a network device using SNMP messages. SNMP can operate over both IPv4 and IPv6 networks56.
DNS: This stands for Domain Name System, which is a protocol that translates human-readable domain names (such as www.example.com) into numerical IPaddresses (such as 192.0.2.1 or 2001:db8::1) that identify network devices. DNS uses a hierarchical distributed database of name servers that store and resolve domain names and IP addresses. DNS can support both IPv4 and IPv6 addresses78.
References: Simple Network Management Protocol - Wikipedia, SNMP over IPv6 - Cisco, Domain Name System - Wikipedia, DNS for IPv6 - Cisco
NEW QUESTION # 39
What is the CLI command to obtain the software version in Ericsson Router 6000 products?
- A. show release
- B. show version
- C. show log
- D. show sysstat
Answer: B
Explanation:
Explanation
The CLI command to obtain the software version in Ericsson Router 6000 products is show version. This command displays information about the software release, the hardware model, the serial number, the uptime, and the boot image of the router. References: [ERICSSON SMARTEDGE 600 HARDWARE MANUAL Pdf Download | ManualsLib], Ericsson Router 6000 Series - Ericsson
NEW QUESTION # 40
Which statement accurately defines an Autonomous System (AS)?
- A. An AS is a network that is capable of autonomously forwarding packets, regardless of direct or indirect connectivity to the Internet.
- B. An AS is a collection of IS-IS routes imported into BGP and presented in such a way that networks connected to the AS have a global overview of the network.
- C. An AS is a group of networks directly connected to each other that can distribute eBGP information using directly established links.
- D. An AS is a set of routers under a single administration, using an interior gateway protocol and common metrics to route packets within the AS.
Answer: D
Explanation:
Explanation
The statement that accurately defines an Autonomous System (AS) is that an AS is a set of routers under a single administration, using an interior gateway protocol and common metrics to route packets within the AS.
An AS is a logical grouping of networks that share a common routing policy and operate under a single administrative authority. An AS can be a single network or a collection of networks that are interconnected by routers. An AS uses an interior gateway protocol (IGP), such as OSPF or IS-IS, to exchange routing information within the AS. An IGP uses common metrics, such as hop count or bandwidth, to determine the best path to each destination within the AS. An AS also has a unique number assigned by IANA, called an AS number (ASN), which identifies the AS in interdomain routing .
References: [Autonomous system (Internet) - Wikipedia], [What Is an Autonomous System? - Cisco]
NEW QUESTION # 41
How do peers recognize each other's ability to use MP-BGP extensions?
- A. They advertise the ability using the capabilities field in the update packet.
- B. They advertise the ability using the capabilities field during the session establishment.
- C. They advertise the ability using the capabilities field in the hello packet.
- D. They advertise the ability using the capabilities field in the End-of-RIB marker.
Answer: B
Explanation:
Explanation
Peers recognize each other's ability to use MP-BGP extensions by advertising the ability using the capabilities field during the session establishment. MP-BGP is an extension to BGP that allows BGP to carry routing information for multiple network layer protocols, such as IPv6, VPNv4, multicast, etc. To support MP-BGP, peers need to exchange their capabilities during the session establishment phase, which consists of three steps:
open, keepalive, and update. In the open message, peers can include an optional parameter called capabilities, which indicates what kind of address families and subsequent address families they can support. If both peers agree on a common set of capabilities, they can proceed to exchange routing information for those address families using update messages56.
References: Use of MP-BGP Extensions for IPv6 Interdomain Routing, MP-EBGP Configuration Example - Cisco
NEW QUESTION # 42
Which two statements are true about priority queuing (PQ)? (Choose two.)
- A. Traffic in the highest priority queue will experience the least amount of jitter and delay compared to traffic in the other queues.
- B. Traffic in the highest priority queue is only reserved for voice traffic.
- C. Traffic in all queues are always guaranteed a minimum bandwidth.
- D. Traffic in lower priority queues can be starved of bandwidth.
Answer: A,D
Explanation:
Explanation
Priority queuing (PQ) is a queuing method that establishes four interface output queues that serve different priority levels: high, medium, normal, and low. Traffic in the highest priority queue will experience the least amount of jitter and delay compared to traffic in the other queues, because PQ always services the higher-priority queues first. However, this can also cause traffic in lower priority queues to be starved of bandwidth, especially if the highest priority queue is oversubscribed. Traffic in the highest priority queue is not only reserved for voice traffic, but can also include network control and routing traffic. Traffic in all queues are not always guaranteed a minimum bandwidth, because PQ does not provide any bandwidth reservation mechanism. References: Quality of Service (QoS) Queues and Queuing Explained, Chapter:
Configuring Priority Queueing - Cisco
NEW QUESTION # 43
What is the purpose of penultimate hop popping?
- A. to reduce the load on the LSP
- B. to reduce the load on the LDP
- C. to reduce the load on the LSR
- D. to reduce the load on the LER
Answer: D
Explanation:
Explanation
Penultimate hop popping (PHP) is a function performed by certain routers in an MPLS enabled network. It refers to the process whereby the outermost label of an MPLS tagged packet is removed by a label switch router (LSR) before the packet is passed to an adjacent label edge router (LER). The purpose of PHP is to reduce the load on the LER, as it saves one cycle of label lookup. The LER can forward the packet based on its IP header or another label in the stack, without having to process the outer label. PHPfunctionality is achieved by the LER advertising a label with a value of 3 to its neighbors. This label is defined as "implicit-null" and informs the neighboring LSRs to perform PHP12.
References: Penultimate hop popping - Wikipedia, MPLS Penultimate hop popping - NetworkLessons.com
NEW QUESTION # 44
IPv6 link-local addresses are designed to be used in which three situations? (Choose three.)
- A. for local IP communication on the IPv6 capable routers
- B. by routers to forward packets with link-local source addresses to other links
- C. for neighbor discovery
- D. addressing on a single link for purposes such as auto-address configuration
- E. when routers are not present
Answer: A,C,D
Explanation:
Explanation
IPv6 link-local addresses are designed to be used in three situations: for neighbor discovery, for local IP communication on the IPv6 capable routers, and for addressing on a single link for purposes such as auto-address configuration. Neighbor discovery is a protocol that allows IPv6 nodes to discover each other and learn their link-layer addresses on a local network. Neighbor discovery uses link-local addresses to send and receive messages such as router advertisements, router solicitations, neighbor advertisements, and neighbor solicitations34. Local IP communication on the IPv6 capable routers refers to the ability of routers to exchange routing information or management traffic using their link-local addresses as source and destination addresses. This reduces the need for global unicast addresses on router interfaces that are not reachable from outside the local network35. Addressing on a single link for purposes such as auto-address configuration refers to the use of link-local addresses to enable IPv6 nodes to obtain an address without manual configuration or a DHCP server. Link-local addresses can be automatically derived from the interface identifier in the modified EUI-64 format or randomly generated. Link-local addresses can also be used to test the connectivity of a link before obtaining a global unicast address36.
References: Understand the IPv6 Link-Local Address - Cisco, Link Local Address - GeeksforGeeks, IPv6 Address Types | Link-Local, Global Unicast, etc. IPCisco, MPLS Label Distribution Protocol Commands - Cisco
NEW QUESTION # 45
......
ECP-206 PDF 100% Cover Real Exam Questions: https://www.actual4dump.com/Ericsson/ECP-206-actualtests-dumps.html
Ericsson ECP-206 Real Exam Questions Guaranteed Updated Dump: https://drive.google.com/open?id=13qxinLVG8pYKMvWe9baIqmDAlNqOWu1j